Thanks for the suggestion, I'll give it a go over the weekend. Do I have to decrypt the recordings on the HDR before they are watchable via network sharing?
I have an HD-T2 which I use to watch recordings via DLNA on an HDR-T2 in another room. The two devices are connected to the network via homeplugs and I've used this setup for some time now without any problems. I've recently changed my router to a D-Link VR900, which has an built-in DLNA...
Admittedly, I haven't used remote scheduling for some time and have just set up my aged mother's HDR to allow me to programme it remotely (and clear out the old stuff that she keeps fogetting how to do). Whenever I've tried going to https://rs.hpkg.tv/ today I get error 503, "The server is...
Hi. Yes, thankyou, I saw the post about the TP-Link firmware update and I read that it mentioned the problem was resolvable by either installing the firmware update or by enabling IGMP on the router (it's already enabled). The Solwise homeplugs are not new by any means and came with the most...
I took the router out of the equation by disconnecting the network cable between it and the homeplug that connects the homeplug network to the rest of the LAN and to the internet. Bingo! I've watched 75 minutes of "Spider House" without any problem at all, with the Humax PVRs still using the...
I'm sure this issue come up before but I couldn't find any previous posts that matched and would appreciate any help.
I have two HDR-T2's connected to my network through DLINK DHP-206AV homeplugs. Playing through these homeplugs and then via wifi to a remote LG smart TV, I can watch HD...
Just putting a USB stick in the front socket and rebooting got it to start properly in maintenance mode. I inadvertently copied the HD firmware onto the stick (it was still in my downloads folder since I updated to CFW2.2 a while ago) onto the stick instead of the new HDR firmware so it got...
Hi all.
I just rebooted my HDR-T2 using the "diagmode" diagnostic so I could clear out old EPG data going back to March this year. After restarting, the box has become unusable; it starts to boot, shows the "Cust FW 2.22" message and then displays "Wait - 59", counts down to 55 and then...
I finally got round to clearing out the old EPG data:
Running: epgrange
Fri Nov 16 00:00:00 GMT 2012
Fri Nov 23 23:55:00 GMT 2012
The EPG display in WebIf is much faster now. Thanks to everyone for helping me to sort it out.
This may be at least partly my own fault. :rolleyes: I checked the channel group for the EPG in the WebIf settings and it seems the channel group is an old one that existed before the recent channel shake-up, containing channels that no longer exist. Changing it to a new group, where all...
Thanks for the suggestions, everyone. I ran epgrange and got the following, somewhat surprising, output:
Running: epgrange
Fri Mar 30 14:55:00 GMT 2012
Sun Nov 18 23:50:00 GMT 2012
I was under the impression that the oldest EPG data dated from 6th October, not 30th March. :eek:
The box...
I've just noticed something odd about the EPG data in my WebIf display: the EPG data goes all the way back to 6th October and many of the old entries have channel number zero, probably because of the channel re-tune that was necessary a few weeks ago. The Webif EPG is very slow to respond...
I see a few people have been asking if af123 would be able to make a few mods to the EPG display in WebIF, so now seems as good a time as any to chip in with a couple of cheeky requests of my own.
I used to use Digiguide (no longer really necessary due to WebIF). One nice option was to show...
All power timers have been deleted and both boxes are behaving themselves overnight now, with no unexpected power-ups.
Thanks for the advice, everyone.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.