Recent content by bob_a_builder

Problem traced to the wi-fli plug which Humax was connected to - It had failed completely this morning, wi-fi plug offline and no power to Humax Only NOW do I recall that whenever my wi-fi plugs have failed in the past they enter a mode where they continuously switch on and off fairly rapidly -...

Not that I'm aware of ..... But that might be relevant, Because I've just pulled an older unit out of storage, and it was initially doing the very same thing - thought I was going mad That unit has been in storage a long time, it managed to stay up long enough to allow me update all the...

That didn't help this time Have now removed Sysmon app as well : rebooted to be sure its cleared out But its still rebooting ...

I've just deleted the monitor.db again, lets see it that stops reboots until tomorrows 04:00 forced reboot

Not from just from standby, as we watch the TV signal from the Humax ( gives better Quality picture) , So we see the reboots happening, but they happen all through the night when we aren't watching Found the fix ? But this morning Sysmon graphs are displaying OK - but the reboots are continuing

Just noticed this issue, where the box is constantly rebooting every few minutes, yet the scheduled recordings seem to take place correctly as expected, in as much as they show in the media list with a correct time length But trying to watch a recording it will still do the rebooting dance Box...

Here is the the monitor.db file zipped up - not sure if it tells you anything viewed it with sqliteviewer myself - that didn't complain of any corruption Renamed the file on the system, effectively deleted, rebooted And now Sysmon is working as expected Thanks for your help

I do have FTP access to the Humax setup via the installed BetaFTP file server package, but only have access to the 3 media folders My Music My Photo My Video How can I access the 'system' folders via FTP ? I see from other threads, people tried copying it to MyVideo but it was still not...

Running fix-flash-packages didn't help I tried running this "cd /mod/monitor && mv monitor.db temp.db && sqlite3 temp.db ".clone monitor.db" && rm temp.db" from above PPR post in the CLI of Telnet But that just told me that monitor.db already exists - which I sort of knew because command it...

Sysmon now only displaying network traffic - previously was displaying all 4 charts OK Had to do a fixdisk yesterday , which was prompted by a notification from the humax boxes diagnostic page - ran fixdisk - 1st pass, found corrupt blocks and remapped multiply linked inodes, finished with a 0...

Have since run a 'fix-flash packages' from the diagnostic , and then done the , save back up of schedule, delete all scheduled events and reboot process Done it twice, and scheduled events were auto restored OK both times - rsvsync log looks same as above

The rsvsync log for the time in question shows this - which look pretty similar to the later entries when I did the manual backup 120 Wed Sep 23 14:46:57 2020: Final schedule entries: 15 119 Wed Sep 23 14:46:57 2020: Slots: +0,+1,+2,+3,+4,+5,+6,+7,+8,+9,+10,+11,+12,+13,+14 118 Wed Sep 23...

@ MymsMan : - Thanks - Yes I did do that - didn't mention in initial post but in an edit a few mins later To be more specific , most of my earlier problems were with it stuck in boot loop issue, the factory default option equiv of system flush at time of drive format , and new drive seem to...

My T2 has entered the dodgy stage lately, randomly crashing and restarting in the setup mode - did put a new drive in etc, seemed better for a week or 2 - now just done it again It would be easier to live with if the Auto-schedule-restore package would do what it supposed to - but its not for...

Still on original 500GB Purchased Oct 2012 ( Grade A refurb from Humax) 9 Power_On_Hours -O--CK 52374 041 041 000 41% - 10 Spin_Retry_Count PO--C- 0 100 100 097 100% - 12 Power_Cycle_Count -O--CK 2014 099 099 020 99% -