Interrupted recordings linked to hard disk problem

I found this under the maintenance mode instructions:

If the web interface hard disk diagnostic highlights attributes 197 or 198 in red, then the additional fix-disk test/repair should run

As my report has 197/198 in red do I run fix-disk test/repair?

thanks

Philip
 
From my previous message:
After the test has completed try creating a new report using the command from the previous message. This time you should see the LBA number of the problem sector near the end of the report. If so, then re-run fix-disk - this should then fix the problem.
 
After test, LBA not found during fix-disk, do I need to add a switch to the command?
Philip

humax# fix-disk
Running /bin/fix-disk
Custom firmware version 2.15


Checking disk sda

Using superblock 0 on sda3
Using superblock 0 on sda1
Using superblock 0 on sda2

Partition /dev/sda1 is already unmounted
Partition /dev/sda2 is already unmounted
Partition /dev/sda3 is already unmounted

Pending sector error(s) found
Running disk self test
Error - pending sectors but LBA not found
humax#
 

Attachments

  • START OF INFORMATION SECTION.pdf
    48 KB · Views: 7
Now I'm baffled. There is a bug in fix-disk, how can it suddenly be fixed? Do you still see the red lines in the smartctl output?

If it is still broken try unzipping and then installing the attached file in normal mode using 'opkg install fix-disk_0.1-1_mipsel.opk'. Once installed run from 'maintenance mode' as before.

Note: This is a 'special', I will come up with a permanent fix later...

Edit: Attachment deleted since it was a special for this particular case.
 
Still seeing the red lines in output.
Humax HD test now reporting no errors, still seeing errors in webif diagnostics.
Will try new fix disk file.
 
Now I'm baffled. There is a bug in fix-disk, how can it suddenly be fixed? Do you still see the red lines in the smartctl output?

If it is still broken try unzipping and then installing the attached file in normal mode using 'opkg install fix-disk_0.1-1_mipsel.opk'. Once installed run from 'maintenance mode' as before.

Note: This is a 'special', I will come up with a permanent fix later...


I am not sure where the install command is looking for the updated fix-disk, do I copy the file to the humax, which directory, or can I point the command at a local copy of the updated fix-disk?

Error message is:

humax# opkg install fix-disk_0.1-1_mipsel.opk
Collected errors:
* make_directory: Cannot create directory `/mod/': File exists.
* make_directory: Cannot create directory `/mod': File exists.
* make_directory: Cannot create directory `/mod': File exists.
* make_directory: Cannot create directory `/mod': File exists.
* pkg_init_from_file: Failed to make temp file /fix-disk_0.1-1_mipsel.opk.control.cH4Kxz: Read-only file system.
* rm_r: Failed to open dir : No such file or directory.
humax#
 
Looks like no errors!
Thanks
Philip


Humax HDR-Fox T2 (humax) 1.02.32/2.15

To return to the menu, type: exit

humax# fix-disk
Running /var/lib/humaxtv_backup/mod/fix-disk
Custom firmware version 2.15


Checking disk sda

Using superblock 0 on sda3
Using superblock 0 on sda1
Using superblock 0 on sda2

Unmounted /dev/sda1
Unmounted /dev/sda2
Unmounted /dev/sda3

Pending sector error(s) found
Error at LBA 948868548
Dev: /dev/sda LBA: 948868548
LBA: 948868548 is on partition /dev/sda2, start: 2104512, bad sector offset: 946764036
dumpe2fs 1.41.14 (22-Dec-2010)
Using superblock 0
Block size: 4096
LBA 948868548 maps to file system block 118345504 on /dev/sda2

Checking to see if this block is in use...
debugfs 1.41.14 (22-Dec-2010)
Block 118345504 is not in use
Do you wish to attempt repair of the bad block? [Y/N]: y

/dev/sda:
re-writing sector 948868548: succeeded

Checking partition /dev/sda3...
e2fsck 1.41.14 (22-Dec-2010)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
hmx_int_stor: 12/655776 files (0.0% non-contiguous), 79870/2622611 blocks

Checking partition /dev/sda1...
e2fsck 1.41.14 (22-Dec-2010)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
hmx_int_stor: 14/65808 files (0.0% non-contiguous), 14742/263062 blocks

Creating swap file...
Setting up swapspace version 1, size = 1073737728 bytes
UUID=8859767c-1c7e-4377-9221-b3a3ee6fda0f

Checking partition /dev/sda2...
e2fsck 1.41.14 (22-Dec-2010)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
hmx_int_stor: 5105/29860704 files (0.9% non-contiguous), 5720703/119209984 blocks
Removing extra swap space.
 
Just to report back. All recordings OKAY. No HD problems. Custom Firmware working really well. thanks. Philip
 
Back
Top