Tuner problems?

catnap

Member
I've got a 16 year old HDR-Fox T2. It has custom firmware, but I doubt if that is relevant to my issue. Over the last 12 months there have been numerous instances of being presented with the setup screen when the unit is switched on. A small nuisance. More recently I get the "no programmes are being broadcast on this channel" message on startup, then after a few minutes (it seems to be taking longer now) I see diagonal zip zag lines of colour across the entire screen, then a heavily pixelated picture and after a couple more minutes all seems ok. The attached TV is receiving its signal via pass thru from the Humax but there is never a problem with the TV picture. I don't use the box to watch lived TV. I record a lot though because we are in a very rural spot with pitiful broadband that makes streaming unreliable.

Perhaps the tuners are failing in some way. I'm inclined to think I've been fortunate to have had such good service for so long (no other audio/video device has lasted as long). Any thoughts? There are a number of threads covering similar but not identical issues but ironically the one that seemed most relevant was started by me and the solution that time was to get a new aerial booster. I think the "new" booster is fine though as other TVs have no picture problems. Any thoughts?
 
Wrong section for CF stuff but...

You could try the flash option from Maintenance Mode to see if it helps with the Setup Wizard.

What are your Strength/Quality readings for each mux from the live menu Settings -> System -> Signal Detection ?
Which channel on which mux (and which transmitter) gives the startup problems?
I had that on my HD, but I think that was due to the suspected slow death of the power supply.
 
Thanks for responding. I didn't think the CF was relevant but mentioned it in case others thought otherwise. Anyway I'm happy to have this moved. I previously tried flash as you describe, but it made no difference. I can live with the Setup problem.

Not sure how to tell definitively which Mux I am on. Oxford is the most likely, but apparently we are in an area where there can be conflict. I suspect we were on Crystal Palace for a while years back. All the channels that I am interested in are on Channel 47 (BBC HD, ITVHD, 4HD). The signal strength for 47 shows as 81 and the quality as 100. But - I can only get this readings when the channels tune in properly. At startup I eventually get a pixelated picture where the onscreen info shows almost no illuminated bars on the signal indicator chain (I assume that is what it is) bottom right of screen.
 
Channel 47 (BBC HD, ITVHD, 4HD). The signal strength for 47 shows as 81
That is PSB3 on Oxford. 81 is rather high. Are you sure you need the "booster"? Can you try without it?
At startup I eventually get a pixelated picture where the onscreen info shows almost no illuminated bars on the signal indicator chain
That matches my symptoms.
 
I disconnected the booster and all channels showed "the receiver is not receiving a signal or the signal is too weak" with 0 strength and quality. I then reconnected the booster and rebooted. I experienced the same cycle of "channel scrambled or unavailable" followed by "no programmes are currently being broadcast on this channel" followed by diagonal zig zags colours then a pixelated picture and finally a clear one. Now however that cycle is taking about 30 seconds to complete where previously it was several minutes. My under-informed thought is this could all be related to the power supply. My wife has pointed out to me that I used to get out of bed as soon as the alarm went off and start the day's tasks alertly whereas now I apparently slowly creak and crack before eventually hobbling up and about for the first 10-15 minutes. Maybe it is just component age.
 
disconnected the booster and all channels showed "the receiver is not receiving a signal or the signal is too weak" with 0 strength and quality.
What is the booster and how much gain has it got? To go from nothing to an excess of signal implies an amp. which has too much gain... but we don't know the state or your received signal, aerial, cabling or anything else about the distribution system (unless you previously posted it - I haven't checked).
Maybe it is just component age.
It might well be, or it might not, or it might be a combination of the two. It's difficult to fault-find without known good kit on a known good aerial feed to start with, or some proper test gear.
 
Your input is much appreciated but I'm not going to take this any further. It is indeed an amp. The layout of the house ia a bit unusual in that it's an old property with a number of extensions. There are several TVs with connections to the amp/booster and it took some time to get good signals on them all and I don't want to change the setup when only the Humax has problems. Unambitious of me I admit. Thanks again.
 
OK, I think we know where the problem probably lies. You may wish to try a 10dB attenuator in the Humax feed. Or not.
 
Back
Top