humax# smartctl -a /dev/sda
smartctl 6.4 2015-06-04 r4109 [7405b0-smp-linux-2.6.18-7.1] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Pipeline HD 5900.2
Device Model: ST31000424CS
Serial Number: 5VX2NYPF
LU WWN Device Id: 5 000c50 04551a068
Firmware Version: SC13
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5900 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Feb 6 15:17:17 2020 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 623) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 214) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 106 087 006 Pre-fail Always - 12516827
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 092 092 020 Old_age Always - 9162
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 438454036567
9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 25911
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 096 096 020 Old_age Always - 4582
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 1036
188 Command_Timeout 0x0032 100 081 000 Old_age Always - 1653587640705
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 440
190 Airflow_Temperature_Cel 0x0022 055 044 045 Old_age Always In_the_past 45 (Min/Max 45/49 #55)
194 Temperature_Celsius 0x0022 045 056 000 Old_age Always - 45 (0 13 0 0 0)
195 Hardware_ECC_Recovered 0x001a 046 037 000 Old_age Always - 12516827
197 Current_Pending_Sector 0x0012 100 082 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 082 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1042 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1042 occurred at disk power-on lifetime: 25721 hours (1071 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 ff ff ff ef 00 1d+05:59:24.333 READ SECTOR(S) EXT
b0 d5 01 06 4f c2 00 00 1d+05:59:24.223 SMART READ LOG
b0 d5 01 00 4f c2 00 00 1d+05:59:24.220 SMART READ LOG
b0 d0 01 00 4f c2 00 00 1d+05:59:24.168 SMART READ DATA
ec 00 01 00 00 00 00 00 1d+05:59:24.155 IDENTIFY DEVICE
Error 1041 occurred at disk power-on lifetime: 25721 hours (1071 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+05:59:21.137 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:21.106 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:19.773 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:19.743 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:18.390 READ DMA EXT
Error 1040 occurred at disk power-on lifetime: 25721 hours (1071 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+05:59:19.773 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:19.743 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:18.390 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:18.360 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:17.027 READ DMA EXT
Error 1039 occurred at disk power-on lifetime: 25721 hours (1071 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+05:59:18.390 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:18.360 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:17.027 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:16.996 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:15.623 READ DMA EXT
Error 1038 occurred at disk power-on lifetime: 25721 hours (1071 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+05:59:17.027 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:16.996 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:15.623 READ DMA EXT
ec 00 00 15 0d 63 a0 00 1d+05:59:15.542 IDENTIFY DEVICE
25 00 08 ff ff ff ef 00 1d+05:59:14.150 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Selective offline Completed without error 00% 25899 -
# 2 Selective offline Completed: read failure 90% 25898 1421735982
# 3 Selective offline Completed: read failure 90% 25898 1421735981
# 4 Selective offline Completed: read failure 90% 25898 1421735976
# 5 Selective offline Completed: read failure 90% 25898 1421734265
# 6 Selective offline Completed: read failure 90% 25898 1421734264
# 7 Selective offline Completed: read failure 90% 25898 1421734263
# 8 Selective offline Completed: read failure 90% 25898 1421734262
# 9 Selective offline Completed: read failure 90% 25898 1421732545
#10 Selective offline Completed: read failure 90% 25898 1421732544
#11 Selective offline Completed: read failure 90% 25898 1421732543
#12 Selective offline Completed: read failure 90% 25898 1421732542
#13 Selective offline Completed: read failure 90% 25898 1421732541
#14 Selective offline Completed: read failure 90% 25898 1421732540
#15 Selective offline Completed: read failure 90% 25898 1421728863
#16 Selective offline Completed: read failure 90% 25898 1421728862
#17 Selective offline Completed: read failure 90% 25898 1421728861
#18 Selective offline Completed: read failure 90% 25898 1421728853
#19 Selective offline Completed: read failure 90% 25898 1421728852
#20 Selective offline Completed: read failure 90% 25898 1421728851
#21 Selective offline Completed: read failure 90% 25898 1421728850
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 1421735982 1953525167 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
