No Recordings, No Disk Capacity?

Black Hole

May contain traces of nut
I'm at a friend's, with an FVP-4000T (I think that's what the label on the bottom says). It has an RM-L08 remote handset with a FreeviewPlay button on it. Press the "recordings" button and it says there aren't any (she says there should be), but tellingly the screen display seems to say that it has zero capacity to record any.

Can anyone suggest how to diagnose? I can't see a settings button on the remote. I've power-cycled it in hope... but that does not seem to have made a difference. Where the heck are the disk utilities???
 
Last edited:
I suspect you're going to have to remove the disc and add it to either a Linux box or HDR Fox T2 to run fixdisc. Given the HDR Fox T2 stayed on an older version once newer versions were found to be putting things in the FS it didn't understand, an HDR Fox T2 might be a safer bet.
 
I'm at a friend's, with an FVP-4000T (I think that's what the label on the bottom says). It has an RM-L08 remote handset with a FreeviewPlay button on it. Press the "recordings" button and it says there aren't any (she says there should be), but tellingly the screen display seems to say that it has zero capacity to record any.

Can anyone suggest how to diagnose? I can't see a settings button on the remote. I've power-cycled it in hope... but that does not seem to have made a difference. Where the heck are the disk utilities???
Settings on the 4000T/5000T are through the Freeview button on the remote control. From there you should be able to navigate to the Disk Check facility.
Freeview button> Settings> PVR Settings> Storage> Internal HDD. HDD Test.
The disk is pretty noisy on these models so stick your ear up close to confirm it is spinning or feel for vibrations.
Download the manual from the Humax UK website. The 4000T is two tones in colour and the 5000T is all black.


Select Freeview Box Recorders under Category then select 4000T or 5000T and then User Manuals and download, go to page 28 for the 4000T.
 
Not likely to be helpful as it looks like the 4000T may have a disk problem but - quite often when my 5000T is switched on and recordings pressed it shows no recordings (not sure about disk status). After a short while the recordings screen disappears and then reloads with a complete list.

Unfortunately, I can't remember what I had to do when the list wouldn't reload. I suspect it involved complete removal of power for over 5 minutes, reboot, factory reset and loss of recordings.
 
I have never understood why "removal of power for over 5 minutes" should make any difference. I admit I didn't do that, just power-cycled it... but even a power-down for a few seconds is a power-down.
 
I have never understood why "removal of power for over 5 minutes" should make any difference. I admit I didn't do that, just power-cycled it... but even a power-down for a few seconds is a power-down.
Possibly allowing a capacitor or inductor to fully discharge. I can remember having a scare with the 5000T along the lines you mention. (Fingers, legs and anything else firmly crossed) It has worked properly since that problem. No removal or replacement of disk. Whilst I can't remember exactly what I did and which bit got things working again, I do remember one or two long power offs (half-one hour). Maybe it'll do something, maybe it won't. What have you got to lose - time.
 
Weirdly this happened to me at the same time. But but with fox t2. Did the unplugged for 1/2 hr hard restart. Nothing. Odd coincidence it’s not software problem is it??

I checked for firmware and latest is 2022. And was to date apparently.
 
Screws hidden behind the anti-tamper labels. Nice.
Fairly common approach, I've come across it multiple times. Including on all the products my previous employer manufactured, with anti tamper labels that you really could not remove and put back on without it showing. But then they were police radios.
 
Back
Top