WebIf Install error

PaulTheOldBarn

New Member
Just discovered this custom firmware (2.20/1.03.06) for the HDR-FOX T2, it sounds superb so I tried installed it but hit a problem installing the full web interface and I'm now stuck.
The custom firmware installed all ok and the basic web i/f appeared correctly. After clicking the install full interface button it successfully downloaded many of the packages but got stuck at (I think) tfmenu due to a lock (/tmp/opkg?) being unavailable. Eventually I restarted the Hummy, hoping to be able to retry but instead get a directory listing - which turns out to be /mnt/hd2/mod/var/mongoose/html
telnet access is fine so the custom firmware is installed ok.
I rolled-back to the standard (1.02.32) firmware and reinstalled the custom firmware to see if that would get me the basic web i/f back but it hasn't.
I've also done the RMA process and reinstalled the custom firmware but now i'm not getting any web interface - it appears as though the custom firmware isn't installing properly as /mnt/hd2/mod is empty but I still have telnet access.
Any ideas on how I could proceed?
 

malcolmg

New Member
I have a similar problem with installing the full web interface as PaulTheOldBarn. The install failed ("hangs/loops") at installing tfmenu, and when I try to connect to the HUMAX I now get a list of folders/directories. Telnet works fine.
I installed the custom firmware (CFW) to resolve the "deleting/looping" problem which it resolved. I would however like to use some of the other features of the CFW, such as decrypting, remote access, copy files over LAN etc. and would be grateful if any of the Humm.tv experts could suggest a way to resolve the failed install.
 
OP
P

PaulTheOldBarn

New Member
Is the front panel display showing '== RMA =='?
Yes! I spotted that just after posting and guessed that where I'd gone wrong was by not installing the standard firmware after the RMA - installing custom firmware didn't reset the RMA. So I installed the standard firmware and then re-installed the custom firmware. That got me the basic web interface back.
This time the installation of the full web i/f got stuck after downloading the initial packages file - again stuck on /tmp/opkg.lock. But this time I manually deleted that file using telnet access and refreshed the web page and then it continued through to success. Hurrah :)
So, if anyone else has problems with installing the full web interface I suggest you use telnet to access the box and do the following
Code:
cd /tmp
rm opkg.lock

Thanks for the rapid responses!
 

malcolmg

New Member
Sorry I have taken so long to respond, I have been having a Scottish New Year!
I have run "
cat /tmp/modinit.log
" as suggested by xyz321 and the output (I am unfamiliar with Putty and
how to collect the output from its window so the command got run twice) is as follows:-

Code:
Menu version 1.07
Enter system PIN: ****
 
/-------------------------\
| T E L N E T M E N U |
\-------------------------/
 
[ Humax HDR-Fox T2 (humax) 1.03.06/2.20 ]
 
1 - Restart into maintenance mode.
2 - Remove web interface password.
stat - Show what the box is currently doing.
x - Exit and close connection.
diag - Run a diagnostic.
cli - System command line (advanced users).
 
Please select option: cli
 
-----------------------------------------------------------------------
Now starting a system command prompt. You can make this the default by
enabling 'Expert mode telnet server' on the web interface settings page.
-----------------------------------------------------------------------
 
Humax HDR-Fox T2 (humax) 1.03.06/2.20
 
To return to the menu, type: exit
 
humax# cat /tmp/modinit.log
=== Sat Jan 1 00:00:11 UTC 2000 - modinit - setup_hosts ======================= ====
=== Sat Jan 1 00:00:12 UTC 2000 - setup hosts ===========================
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
Interface: [eth0]
IP: [192.168.0.6]
=== Sat Jan 1 00:00:12 UTC 2000 - complete ===========================
=== Sat Jan 4 13:20:48 UTC 2014 - modinit - ===========================
=== Sat Jan 4 13:20:48 UTC 2014 - diag ===========================
Filesystem Size Used Available Use% Mounted on
/dev/root 20.9M 20.9M 0 100% /
tmpfs 61.0M 28.0K 61.0M 0% /tmp
tmpfs 61.0M 0 61.0M 0% /media
/dev/mtdblock1 2.0M 568.0K 1.4M 28% /var/lib/humaxtv
/dev/mtdblock2 2.0M 1.2M 804.0K 61% /var/lib/humaxtv_backup
/dev/sda1 1011.4M 34.5M 925.6M 4% /mnt/hd1
/dev/sda2 447.6G 379.5G 45.4G 89% /mnt/hd2
/dev/sda3 9.8G 461.4M 8.9G 5% /mnt/hd3
 
eth0 Link encap:Ethernet HWaddr DC:D3:21:09:D2:48
inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:762 (762.0 B) TX bytes:664 (664.0 B)
Interrupt:16
 
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
 
 
PID USER VSZ STAT COMMAND
1 root 1244 S init
2 root 0 SW [migration/0]
3 root 0 SWN [ksoftirqd/0]
4 root 0 SW [migration/1]
5 root 0 SWN [ksoftirqd/1]
6 root 0 SW< [events/0]
7 root 0 SW< [events/1]
8 root 0 SW< [khelper]
9 root 0 SW< [kthread]
10 root 0 SW< [kblockd/0]
11 root 0 SW< [kblockd/1]
12 root 0 SW< [khubd]
13 root 0 SW< [kseriod]
14 root 0 SW [pdflush]
15 root 0 SW [pdflush]
16 root 0 SW< [kswapd0]
17 root 0 SW< [aio/0]
18 root 0 SW< [aio/1]
19 root 0 SW< [ata/0]
20 root 0 SW< [ata/1]
21 root 0 SW< [ata_aux]
22 root 0 SW< [scsi_eh_0]
23 root 0 SW< [scsi_eh_1]
24 root 0 SW [mtdblockd]
25 root 0 SW< [kpsmoused]
26 root 1240 S {rcS} /bin/sh /etc/init.d/rcS
71 root 0 SWN [jffs2_gcd_mtd1]
72 root 0 SWN [jffs2_gcd_mtd2]
129 nobody 936 S /usr/bin/dnsmasq
135 root 812 S N /sbin/utelnetd -l /bin/tmenu -p 23 -d -B
151 root 1244 S {S90settop} /bin/sh /etc/init.d/S90settop start
161 root 325m S /usr/bin/humaxtv
319 root 1248 S udhcpc -t 5 -T 10 -p /var/lib/humaxtv/udhcpc.eth0.pid -i eth0
338 root 840 S tinyftp -i HumaxFTP -p 0000 -c /media
379 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
396 root 0 SW< [kjournald]
399 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
427 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
442 root 0 SW< [kjournald]
449 root 0 SW< [kjournald]
480 root 1228 S < sleep 1
511 root 1252 R < {modinit} /bin/sh /sbin/modinit
517 root 476 R < date +%d/%m/%Y %H:%M
524 root 1236 R < ps -w
 
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
 
=== Sat Jan 4 13:20:49 UTC 2014 - reset all ===========================
=== Sat Jan 4 13:20:49 UTC 2014 - rma ===========================
=== Sat Jan 4 13:20:49 UTC 2014 - ugprade bootmod ===========================
=== Sat Jan 4 13:20:49 UTC 2014 - setup directories ===========================
=== Sat Jan 4 13:20:49 UTC 2014 - create modenv ===========================
=== Sat Jan 4 13:20:49 UTC 2014 - create rcS ===========================
=== Sat Jan 4 13:20:50 UTC 2014 - migrate bootmod ===========================
=== Sat Jan 4 13:20:50 UTC 2014 - setup hostname ===========================
=== Sat Jan 4 13:20:50 UTC 2014 - setup hosts ===========================
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
Interface: [eth0]
IP: [192.168.0.6]
=== Sat Jan 4 13:20:50 UTC 2014 - run init ===========================
killall: bootstrapd: no process killed
Anacron 2.3 started on 2014-01-04
Normal exit (0 jobs run)
=== Sat Jan 4 13:20:51 UTC 2014 - complete ===========================
Loading config file /mod/etc/mongoose.conf
humax# Humax HDR-Fox T2 (humax) 1.03.06/2.20
/bin/sh: syntax error: unexpected "("
humax#
humax# To return to the menu, type: exit
/bin/sh: To: not found
humax#
humax# humax# cat /tmp/modinit.log
/bin/sh: humax#: not found
humax# === Sat Jan 1 00:00:11 UTC 2000 - modinit - setup_hosts =======================
====
/bin/sh: ===: not found
humax# === Sat Jan 1 00:00:12 UTC 2000 - setup hosts ===========================
/bin/sh: ===: not found
humax# Kernel IP routing table
/bin/sh: Kernel: not found
humax# Destination Gateway Genmask Flags Metric Ref Use Iface
/bin/sh: Destination: not found
humax# 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
/bin/sh: 192.168.0.0: not found
humax# default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
/bin/sh: default: not found
humax# Interface: [eth0]
/bin/sh: Interface:: not found
humax# IP: [192.168.0.6]
/bin/sh: IP:: not found
humax# === Sat Jan 1 00:00:12 UTC 2000 - complete ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:48 UTC 2014 - modinit - ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:48 UTC 2014 - diag ===========================
/bin/sh: ===: not found
humax# Filesystem Size Used Available Use% Mounted on
/dev/root 20.9M 20.9M 0 100% /
/bin/sh: Filesystem: not found
humax# /dev/root 20.9M 20.9M 0 100% /
/bin/sh: /dev/root: not found
humax# tmpfs 61.0M 28.0K 61.0M 0% /tmp
/bin/sh: tmpfs: not found
humax# tmpfs 61.0M 0 61.0M 0% /media
/bin/sh: tmpfs: not found
humax# /dev/mtdblock1 2.0M 568.0K 1.4M 28% /var/lib/humaxtv
/dev/mtdblock2 2.0M 1.2M 804.0K 61% /var/lib/humaxtv_backup
/bin/sh: /dev/mtdblock1: Permission denied
humax# /dev/mtdblock2 2.0M 1.2M 804.0K 61% /var/lib/humaxtv_backup
 
/bin/sh: /dev/mtdblock2: Permission denied
/dev/sda2 447.6G 379.5G 45.4G 89% /mnt/hd2
humax# /dev/sda1 1011.4M 34.5M 925.6M 4% /mnt/hd1
 
inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0/bin/sh: /dev/sda1: Permission denied
 
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1humax# /dev/sda2 447.6G 379.5G 45.4G 89% /mnt/hd2
RX packets:3 errors:0 dropped:0 overruns:0 frame:0/bin/sh: /dev/sda2: Permission denied
humax# /dev/sda3 9.8G 461.4M 8.9G 5% /mnt/hd3
/bin/sh: /dev/sda3: Permission denied
humax#
humax# eth0 Link encap:Ethernet HWaddr DC:D3:21:09:D2:48
/bin/sh: eth0: not found
humax# inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0
/bin/sh: inet: not found
humax# UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
/bin/sh: UP: not found
humax# RX packets:3 errors:0 dropped:0 overruns:0 frame:0
/bin/sh: RX:
not found
humax# TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
RX packets:0 errors:0 dropped:0 overruns:0 frame:0/bin/sh: TX: not found
humax# collisions:0 txqueuelen:1000
/bin/sh: collisions:0: not found
humax# RX bytes:762 (762.0 B) TX bytes:664 (664.0 B)
 
/bin/sh: syntax error: unexpected "("
humax# Interrupt:16
/bin/sh: Interrupt:16: not found
humax#
collisions:0 txqueuelen:0humax# lo Link encap:Local Loopback
/bin/sh: lo: not found
humax# inet addr:127.0.0.1 Mask:255.0.0.0
/bin/sh: inet: not found
humax# UP LOOPBACK RUNNING MTU:16436 Metric:1
/bin/sh: UP: not found
humax# RX packets:0 errors:0 dropped:0 overruns:0 frame:0
/bin/sh: RX: not found
humax# TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
/bin/sh: TX: not found
humax# collisions:0 txqueuelen:0
/bin/sh: collisions:0: not found
humax# RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
/bin/sh: syntax error: unexpected "("
humax#
humax#
humax# PID USER VSZ STAT COMMAND
/bin/sh: PID: not found
humax# 1 root 1244 S init
/bin/sh: 1: not found
humax# 2 root 0 SW [migration/0]
/bin/sh: 2: not found
humax# 3 root 0 SWN [ksoftirqd/0]
/bin/sh: 3: not found
humax# 4 root 0 SW [migration/1]
/bin/sh: 4: not found
humax# 5 root 0 SWN [ksoftirqd/1]
/bin/sh: 5: not found
humax# 6 root 0 SW< [events/0]
/bin/sh: can't open [events/0]: no such file
/bin/sh: 6: not found
humax# 7 root 0 SW< [events/1]
/bin/sh: can't open [events/1]: no such file
/bin/sh: 7: not found
humax# 8 root 0 SW< [khelper]
/bin/sh: can't open [khelper]: no such file
/bin/sh: 8: not found
humax# 9 root 0 SW< [kthread]
/bin/sh: can't open [kthread]: no such file
/bin/sh: 9: not found
humax# 10 root 0 SW< [kblockd/0]
/bin/sh: can't open [kblockd/0]: no such file
/bin/sh: 10: not found
humax# 11 root 0 SW< [kblockd/1]
/bin/sh: can't open [kblockd/1]: no such file
/bin/sh: 11: not found
humax# 12 root 0 SW< [khubd]
/bin/sh: can't open [khubd]: no such file
/bin/sh: 12: 15 root 0 SW [pdflush]not found
humax# 13 root 0 SW< [kseriod]
/bin/sh: can't open [kseriod]: no such file
 
/bin/sh: 13: not found
humax# 14 root 0 SW [pdflush]
/bin/sh: 14: not found
humax# 15 root 0 SW [pdflush]
/bin/sh: 15: not found
humax# 16 root 0 SW< [kswapd0]
/bin/sh: can't open [kswapd0]: no such file
/bin/sh: 16: not found
 
humax# 17 root 0 SW< [aio/0]
/bin/sh: can't open [aio/0]: no such file
/bin/sh: 17: not found
humax# 18 root 0 SW< [aio/1]
/bin/sh: can't open [aio/1]: no such file
/bin/sh: 18: not found
humax# 19 root 0 SW< [ata/0]
/bin/sh: can't open [ata/0]: no such file
/bin/sh: 19: not found
humax# 20 root 0 SW< [ata/1]
/bin/sh: can't open [ata/1]: no such file
/bin/sh: 20: not found
humax# 21 root 0 SW< [ata_aux]
/bin/sh: can't open [ata_aux]: no such file
/bin/sh: 21: not found
humax# 22 root 0 SW< [scsi_eh_0]
/bin/sh: can't open [scsi_eh_0]: no such file
/bin/sh: 22: not found
humax# 23 root 0 SW< [scsi_eh_1]
/bin/sh: can't open [scsi_eh_1]: no such file
/bin/sh: 23: not found
humax# 24 root 0 SW [mtdblockd]
/bin/sh: 24: not found
humax# 25 root 0 SW< [kpsmoused]
/bin/sh: can't open [kpsmoused]: no such file
/bin/sh: 25: not found
26 root 1240 S {rcS} /bin/sh /etc/init.d/rcS
humax# 26 root 1240 S {rcS} /bin/sh /etc/init.d/rcS
/bin/sh: 26: not found
humax# 71 root 0 SWN [jffs2_gcd_mtd1]
/bin/sh: 71: not found
humax# 72 root 0 SWN [jffs2_gcd_mtd2]
/bin/sh: 72: not found
humax# 129 nobody 936 S /usr/bin/dnsmasq
/bin/sh: 129: not found
humax# 135 root 812 S N /sbin/utelnetd -l /bin/tmenu -p 23 -d -B
/bin/sh 151 root 1244 S {S90settop} /bin/sh /etc/init.d/S90settop start: 135: not found
humax# 151 root 1244 S {S90settop} /bin/sh /etc/init.d/S90settop start
161 root 325m S /usr/bin/humaxtv/bin/sh: 151: not found
humax# 161 root 325m S /usr/bin/humaxtv
/bin/sh: 161: not found
humax# 319 root 1248 S udhcpc -t 5 -T 10 -p /var/lib/humaxtv/udhcpc.eth0.pid
-i eth0
 
/bin/sh: 319: not found
humax# 338 root 840 S tinyftp -i HumaxFTP -p 0000 -c /media
 
/bin/sh: 338: not found
humax# 379 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
/bin/sh: can't open {run-and-gun}: no such file
/bin/sh: 379: not found
humax# 396 root 0 SW< [kjournald]
/bin/sh: can't open [kjournald]: no such file
/bin/sh: 396: not found
humax# 399 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
/bin/sh: can't open {run-and-gun}: no such file
/bin/sh: 399: not found
humax# 427 root 1260 S < {run-and-gun} /bin/sh /etc/mdev/run-and-gun
/bin/sh: can't open {run-and-gun}: no such file
442 root 0 SW< [kjournald]/bin/sh: 427: not found
humax# 442 root 0 SW< [kjournald]
/bin/sh: can't open [kjournald]: no such file
/bin/sh: 442: not found
humax# 449 root 0 SW< [kjournald]
/bin/sh: can't open [kjournald]: no such file
480 root 1228 S < sleep 1/bin/sh: 449: not found
humax# 480 root 1228 S < sleep 1
/bin/sh: can't open sleep: no such file
/bin/sh: 480: not found
humax# 511 root 1252 R < {modinit} /bin/sh /sbin/modinit
/bin/sh: can't open {modinit}: no such file
/bin/sh: 511: not found
humax# 517 root 476 R < date +%d/%m/%Y %H:%M
/bin/sh: can't open date: no such file
/bin/sh: 517: not found
humax# 524 root 1236 R < ps -w
/bin/sh: can't open ps: no such file
/bin/sh: 524: not found
humax#
humax# Kernel IP routing table
/bin/sh: Kernel: not found
humax# Destination Gateway Genmask Flags Metric Ref Use Iface
/bin/sh: Destination: not found
humax# 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
 
/bin/sh: 192.168.0.0: not found
humax# default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
/bin/sh: default: not found
humax#
humax# === Sat Jan 4 13:20:49 UTC 2014 - reset all ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:49 UTC 2014 - rma ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:49 UTC 2014 - ugprade bootmod ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:49 UTC 2014 - setup directories ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:49 UTC 2014 - create modenv ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:49 UTC 2014 - create rcS ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:50 UTC 2014 - migrate bootmod ===========================
=== Sat Jan 4 13:20:50 UTC 2014 - setup hostname ===========================/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:50 UTC 2014 - setup hostname ===========================
/bin/sh: ===: not found
humax# === Sat Jan 4 13:20:50 UTC 2014 - setup hosts ===========================
/bin/sh: ===: not found
humax# Kernel IP routing table
/bin/sh: Kernel: not found
humax# Destination Gateway Genmask Flags Metric Ref Use Iface
 
/bin/sh: Destination: not found
humax# 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
/bin/sh: 192.168.0.0: not found
humax# default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
/bin/sh: default: not found
humax# Interface: [eth0]
/bin/sh: Interface:: not found
humax# IP: [192.168.0.6]
/bin/sh: IP:: not found
humax# === Sat Jan 4 13:20:50 UTC 2014 - run init ===========================
killall: bootstrapd: no process killed/bin/sh: ===: not found
humax# killall: bootstrapd: no process killed
 
/bin/sh: killall:: not found
humax# Anacron 2.3 started on 2014-01-04
Normal exit (0 jobs run)/bin/sh: Anacron: not found
humax# Normal exit (0 jobs run)
/bin/sh: syntax error: unexpected "("
humax# === Sat Jan 4 13:20:51 UTC 2014 - complete ===========================
/bin/sh: ===: not found
humax# Loading config file /mod/etc/mongoose.conf
/bin/sh: Loading: not found
humax# humax


I hope this is meaningful.
Many thanks.
 

xyz321

Well-Known Member
I think the errors shown above are because when cutting and pasting, the text has been pasted back into the PuTTy window.

Can you try:
Code:
opkg install webif --force-reinstall
 

malcolmg

New Member
Hi xyz321,
I have tried the command you suggest and get the output below. The various installs proceed very rapidly, I can here the Hummy's disc working to install but it stops at the package indicated.

Code:
Menu version 1.07
Enter system PIN: ****

      /-------------------------\
      |  T E L N E T   M E N U  |
      \-------------------------/

  [ Humax HDR-Fox T2 (humax) 1.03.06/2.20 ]

    1 - Restart into maintenance mode.
    2 - Remove web interface password.
 stat - Show what the box is currently doing.
    x - Exit and close connection.
 diag - Run a diagnostic.
  cli - System command line (advanced users).

Please select option: cli

-----------------------------------------------------------------------
Now starting a system command prompt. You can make this the default by
enabling 'Expert mode telnet server' on the web interface settings page.
-----------------------------------------------------------------------

Humax HDR-Fox T2 (humax) 1.03.06/2.20

To return to the menu, type: exit

humax# opkg install webif --force-reinstall
No packages removed.
Installing webif (1.0.7-11) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif_1.0.7-11_mipsel.opk[/url].
Installing webif-channelicons (1.1.8) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif-channelicons_1.1.8_mipsel.opk[/url].
Installing mongoose (3.0.10) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/mongoose_3.0.10_mipsel.opk[/url].
Installing jim (0.74-4) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim_0.74-4_mipsel.opk[/url].
Installing jim-oo (0.71) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-oo_0.71_mipsel.opk[/url].
Installing jim-sqlite3 (0.74-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-sqlite3_0.74-1_mipsel.opk[/url].
Installing sqlite3 (3.7.6) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/sqlite3_3.7.6_mipsel.opk[/url].
Installing jim-cgi (0.7) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-cgi_0.7_mipsel.opk[/url].
Installing jim-binary (0.74) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-binary_0.74_mipsel.opk[/url].
Installing service-control (1.2) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/service-control_1.2_mipsel.opk[/url].
Installing busybox (1.20.2-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/busybox_1.20.2-1_mipsel.opk[/url].
Installing lsof (4.82) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/lsof_4.82_mipsel.opk[/url].
Installing epg (1.0.13) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/epg_1.0.13_mipsel.opk[/url].
Installing hmt (1.1.16) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/hmt_1.1.16_mipsel.opk[/url].
Installing ssmtp (2.64) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/ssmtp_2.64_mipsel.opk[/url].
Installing anacron (2.3-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/anacron_2.3-1_mipsel.opk[/url].
Installing cron-daemon (1.18.3-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/cron-daemon_1.18.3-1_mipsel.opk[/url]
Installing trm (1.1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/trm_1.1_mipsel.opk[/url].
Installing openssl-command (1.0.0.d) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/openssl-command_1.0.0.d_mipsel[/url].
Installing nicesplice (1.5) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/nicesplice_1.5_mipsel.opk[/url].
Installing id3v2 (0.1.11-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/id3v2_0.1.11-1_mipsel.opk[/url].
Installing file (5.0.4) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/file_5.0.4_mipsel.opk[/url].
Installing rsvsync (1.0.3) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/rsvsync_1.0.3_mipsel.opk[/url].
Installing webif-charts (1.2) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif-charts_1.2_mipsel.opk[/url].
Installing stripts (1.2.5) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/stripts_1.2.5_mipsel.opk[/url].
Installing smartmontools (5.41) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/smartmontools_5.41_mipsel.opk[/url].
Installing tmenu (1.05) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/tmenu_1.05_mipsel.opk[/url].
Installing ffmpeg (0.10) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/ffmpeg_0.10_mipsel.opk[/url].
 

af123

Administrator
Staff member
That package is larger than most of the others so may take a bit longer..
 

malcolmg

New Member
Thanks af123, I tried the install again and got a failure at the same module, this time the download timed out. The log is :-

Code:
Menu version 1.07
Enter system PIN: ****

      /-------------------------\
      |  T E L N E T   M E N U  |
      \-------------------------/

  [ Humax HDR-Fox T2 (humax) 1.03.06/2.20 ]

    1 - Restart into maintenance mode.
    2 - Remove web interface password.
 stat - Show what the box is currently doing.
    x - Exit and close connection.
 diag - Run a diagnostic.
  cli - System command line (advanced users).

Please select option: cli

-----------------------------------------------------------------------
Now starting a system command prompt. You can make this the default by
enabling 'Expert mode telnet server' on the web interface settings page.
-----------------------------------------------------------------------

Humax HDR-Fox T2 (humax) 1.03.06/2.20

To return to the menu, type: exit

humax# opkg install webif --force-reinstall
No packages removed.
Installing webif (1.0.7-11) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif_1.0.7-11_mipsel.opk[/url].
Installing webif-channelicons (1.1.8) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif-channelicons_1.1.8_mipsel.opk[/url].
Installing mongoose (3.0.10) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/mongoose_3.0.10_mipsel.opk[/url].
Installing jim (0.74-4) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim_0.74-4_mipsel.opk[/url].
Installing jim-oo (0.71) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-oo_0.71_mipsel.opk[/url].
Installing jim-sqlite3 (0.74-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-sqlite3_0.74-1_mipsel.opk[/url].
Installing sqlite3 (3.7.6) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/sqlite3_3.7.6_mipsel.opk[/url].
Installing jim-cgi (0.7) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-cgi_0.7_mipsel.opk[/url].
Installing jim-binary (0.74) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/jim-binary_0.74_mipsel.opk[/url].
Installing service-control (1.2) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/service-control_1.2_mipsel.opk[/url].
Installing busybox (1.20.2-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/busybox_1.20.2-1_mipsel.opk[/url].
Installing lsof (4.82) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/lsof_4.82_mipsel.opk[/url].
Installing epg (1.0.13) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/epg_1.0.13_mipsel.opk[/url].
Installing hmt (1.1.16) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/hmt_1.1.16_mipsel.opk[/url].
Installing ssmtp (2.64) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/ssmtp_2.64_mipsel.opk[/url].
Installing anacron (2.3-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/anacron_2.3-1_mipsel.opk[/url].
Installing cron-daemon (1.18.3-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/cron-daemon_1.18.3-1_mipsel.opk[/url]
Installing trm (1.1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/trm_1.1_mipsel.opk[/url].
Installing openssl-command (1.0.0.d) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/openssl-command_1.0.0.d_mipsel[/url].
Installing nicesplice (1.5) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/nicesplice_1.5_mipsel.opk[/url].
Installing id3v2 (0.1.11-1) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/id3v2_0.1.11-1_mipsel.opk[/url].
Installing file (5.0.4) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/file_5.0.4_mipsel.opk[/url].
Installing rsvsync (1.0.3) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/rsvsync_1.0.3_mipsel.opk[/url].
Installing webif-charts (1.2) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/webif-charts_1.2_mipsel.opk[/url].
Installing stripts (1.2.5) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/stripts_1.2.5_mipsel.opk[/url].
Installing smartmontools (5.41) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/smartmontools_5.41_mipsel.opk[/url].
Installing tmenu (1.05) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/tmenu_1.05_mipsel.opk[/url].
Installing ffmpeg (0.10) to root...
Downloading [url]http://hummypkg.org.uk/hdrfoxt2/base/ffmpeg_0.10_mipsel.opk[/url].
wget: download timed out
Configuring sqlite3.
Configuring mongoose.
Configuring tmenu.
Configuring busybox.
Configuring lsof.
Configuring ssmtp.
Configuring openssl-command.
Configuring nicesplice.
Configuring cron-daemon.
Configuring anacron.
grep: /mod//var/spool/cron/crontabs/root: No such file or directory
Configuring jim.
Configuring jim-binary.
Configuring stripts.
Configuring jim-cgi.
Configuring service-control.
Configuring webif-charts.
Configuring smartmontools.
Configuring webif-channelicons.
Configuring jim-sqlite3.
Configuring file.
Configuring id3v2.
Configuring epg.
Configuring trm.
Configuring hmt.
Configuring jim-oo.
Configuring rsvsync.
Collected errors:
 * opkg_download: Failed to download [url]http://hummypkg.org.uk/hdrfoxt2/base/ffmpeg_0.10_mipsel.opk[/url], wget returned 1.
 * opkg_install_pkg: Failed to download ffmpeg. Perhaps you need to run 'opkg update'?
 * opkg_install_cmd: Cannot install package webif.
humax#

I ran the 'opkg update' as suggested and it seemed to complete but my problem remains that I get a directory/folder list when I try to access the HUMAX via browser.

Any help gratefully received.
 

af123

Administrator
Staff member
If the download of ffmpeg is timing out then it indicates a network problem somewhere. Try just installing that package from the command line.

opkg install ffmpeg

Does it still time out?

If so, try this command

ifconfig eth0 mtu 1200

Then try installing ffmpeg again.
 

malcolmg

New Member
Thanks af123, it installed without problems, see below, but I cannot see what I need to do now to get the webif going - still getting a directory list when I browse to the HUMAX.
Ho Hum, I am starting to lose heart and I get the feeling that I am upsetting forum moderators by not posting correctly.
Is it worth continuing with the webif?

Code:
Menu version 1.07
Enter system PIN: ****
 
      /-------------------------\
      |  T E L N E T  M E N U  |
      \-------------------------/
 
  [ Humax HDR-Fox T2 (humax) 1.03.06/2.20 ]
 
    1 - Restart into maintenance mode.
    2 - Remove web interface password.
stat - Show what the box is currently doing.
    x - Exit and close connection.
diag - Run a diagnostic.
  cli - System command line (advanced users).
 
Please select option: cli
 
-----------------------------------------------------------------------
Now starting a system command prompt. You can make this the default by
enabling 'Expert mode telnet server' on the web interface settings page.
-----------------------------------------------------------------------
 
Humax HDR-Fox T2 (humax) 1.03.06/2.20
 
To return to the menu, type: exit
 
humax# opkg install ffmpeg
Installing ffmpeg (0.10) to root...
Downloading http://hummypkg.org.uk/hdrfoxt2/base/ffmpeg_0.10_mipsel.opk.
Installing bzip2 (1.0.4) to root...
Downloading http://hummypkg.org.uk/hdrfoxt2/base/bzip2_1.0.4_mipsel.opk.
Installing lamemp3 (3.98.4) to root...
Downloading http://hummypkg.org.uk/hdrfoxt2/base/lamemp3_3.98.4_mipsel.opk.
Configuring bzip2.
Configuring lamemp3.
Configuring ffmpeg.
humax#
 

Ezra Pound

Well-Known Member
Until af123 returns, you could try service from the humax# prompt e.g. :-
Code:
humax# service
 
Name                Installed  Autostart  Running
----                ---------  ---------  -------
mediatomb            No        No        No
dropbear            No        No        No
transmission        Yes        No        No
samba                No        No        No
nfs                  No        No        No
cifs                No        No        No
mongoose            Yes        Yes        Yes
betaftpd            Yes        Yes        Yes
 
Syntax:
        service start <service>
        service stop <service>
        service auto <service>          (toggles autostart)
 
humax#
 

malcolmg

New Member
Hi af123, i tried as ezra pound suggested and found that only one service is running "mongoose".

Code:
Menu version 1.07
Enter system PIN: ****
 
      /-------------------------\
      |  T E L N E T  M E N U  |
      \-------------------------/
 
  [ Humax HDR-Fox T2 (humax) 1.03.06/2.20 ]
 
    1 - Restart into maintenance mode.
    2 - Remove web interface password.
stat - Show what the box is currently doing.
    x - Exit and close connection.
diag - Run a diagnostic.
  cli - System command line (advanced users).
 
Please select option: cli
 
-----------------------------------------------------------------------
Now starting a system command prompt. You can make this the default by
enabling 'Expert mode telnet server' on the web interface settings page.
-----------------------------------------------------------------------
 
Humax HDR-Fox T2 (humax) 1.03.06/2.20
 
To return to the menu, type: exit
 
humax# service
 
Name                Installed  Autostart  Running
----                ---------  ---------  -------
mediatomb            No        No        No
dropbear            No        No        No
transmission        No        No        No
samba                No        No        No
nfs                  No        No        No
cifs                No        No        No
mongoose            Yes        Yes        Yes
betaftpd            No        No        No
 
Syntax:
        service start <service>
        service stop <service>
        service auto <service>          (toggles autostart)
 
humax#
 

af123

Administrator
Staff member
Now that ffmpeg has installed, try the webif installation again.

opkg install webif

This is happening to a few too many people, I'll need to think of a way of recovering more gracefully than this!
 

malcolmg

New Member
Many thanks af123 (and all the others who contributed) I have the webif running, great!
Probably too late now to start getting into the features at 22:50.
 

Brian

Administrator
Staff member
Ho Hum, I am starting to lose heart and I get the feeling that I am upsetting forum moderators by not posting correctly.
Don't worry you are not upsetting forum moderators, I have added code tags to your previous posts in this thread. :)
 

malcolmg

New Member
Thanks brian, I think I've got the hang of "code tags" now and will certainly use them when posting large outputs in future.
 

James Wilson

New Member
I am a newbie to HDR-FOX T2, though have been hacking my AppleTV2 for a while.

Just received my unit from HumaxDirect in Brentford, and I also hit this issue on first two install attempts, before resorting to the forum.

About to try and recall how to telnet and will try

cd /tmp

rm opkg.lock

James W
 
Top